Chem-FreeIRON REDUCTION SYSTEMSINSTALLATION AND OPERATING INSTRUCTIONSChem-Free Iron Filter ModelsAqua-Pure® Models: APIF075 APIF075M APIF100 APIF
3-2NOTE: Have you read “ Section 4”, PLUMBING SYSTEM CLEANUP, for instructions on some procedures that may need to be performed fi rst?GRAVEL AND CHEM-
Figure 2: HYDRO-CHARGER INSTALLATION3-3Step 2 Shut off water at main supply. On a PRIVATE WELL SYSTEM turn off the power to the WELL PUMP and drain
3-4OFFOFFOFFOFFOFFOFFOFFOFFOFFOFFOFFOFFSupply WaterEntersSupply (Untreated)Water ExitsSupply WaterEntersTreated WaterExitsNORMAL OPERATION BYPASS OPER
Step 9Fitting Installation Instructions 1) The installation fi ttings are designed to accommodate minor plumbing line and fi ttings. 2) Thread tape
Step 11 Plug the control valve into a properly grounded 110/120V 60 Hz non switched electrical outlet. Check with your local code enforcement offi ce
Personsin FamilyIRON CONTENT - (PPM)2468101214161 12121212121212122 121212666643 12126664434 1266443325 1266433226 126433221Models MCIF 0751, 0751MAPI
Personsin FamilyIRON CONTENT - (PPM)5 10121416182022242628301 1212121212121212121212122 12121212121212666663 1212126666666444 121266666444445 12666444
3-9HOW TO SET TIME OF DAYSTEP 1 - Press SET HOUR and release.STEP 2 - Set the clock display to the closest hour by pressing the or . An arrow wi
HOW TO CHANGE DAYS BETWEEN REGENERATIONSTEP 1 - Press and hold SET HOUR and buttons simultaneously for three (3) seconds and release.STEP 2 - Press
Control Valve Function and Cycles of OperationThe AC adapter comes with a 15 foot power cord that is designed for use with the control valve. The AC
SAFETY INFORMATIONEXPLANATION OF SIGNAL WORD CONSEQUENCESWARNINGCAUTIONRead, understand, and follow all safety information contained in these instruct
HOW TO SET TIMER CONTROLSETHOURRegenMin. FillRegenHourTime - HourPMDays To RegenPower LossIf the power goes out, current time of day will need to be r
Installation must comply with state and local plumbing codes. Failure to follow installation, operation and maintenance instructions may resu
3-14Figure 10Figure 11Figure 8Figure 9
SECTION 4: MAINTENANCE The following procedures are guidelines only but have proven successful in most instances. Under no circum-stances should any
SECTION 5: Backwashing InstructionsPeriodic Backwashing of the Chem-Free Filter System bed is required to fl ush out the entrapped iron that has accumu
Problem Cause Solution1. Timer does not display time of day a. AC adapter unplugged a. Connect powerb. No electric power at outlet b. Repair outle
Problem Cause Solution1. Water CLEAR when drawn, turns RED upon standing (Stain producing)a. Insuffi cient air-draw by Hydro-Charger. a. Check H
SECTION 7: VALVE SPECIFICATION AND OPERATING DATAMaximum Service Flow Rate:Includes Bypass Valve27 gpm (102.2 lpm) @15 psig (103 kPa) dropMaximum Bac
SECTION 7: SPECIFICATION AND OPERATING DATA1) Replenishment of pH adjusting component of media may be required periodically, the frequency of which is
7-3Ref.No.DescriptionMCIF0751 MCIF0751M APIF075S APIF075MMCIF1001 MCIF1001M APIF100S APIF100MMCIF1501 MCIF1501M APIF150S APIF150MMCIF2001
IMPORTANT NOTES • The system should be installed on cold water lines only. • SHUT OFF FUEL SUPPLY TO WATER HEATER after water is shut off. •
SECTION 7: COMPONENTS ASSEMBLIESCHEM-FREE IRON FILTER ASSEMBLIES AND COMPONENTS DRIVE CAP ASSEMBLY, DOWNFLOW PISTON, AND SPACE STACK ASSEMBLIES Refere
SECTION 7: FRONT COVER AND DRIVE ASSEMBLY Reference No. Part No. Description Quantity 1 V3175TC-01 Time Clock Front Cover Assembly 1
SECTION 7: QUICK CONNECT BYPASS Part Number V3006Reference No. Part No. Description Quantity 1 V3151 Nut 1” Quick Connect 2 2 V3150
7-7SECTION 7: INSTALLATION FITTING AND ASSEMBLIESQuick Connect AssembliesPart # V3007-021” Copper Brass Sweat Adapter Reference No. Part No.
7-84652713WaterFlowProper DLFC orientationdirects water flow towardsthe washer face withrounded edge.Reference No. Part No. Description Quantity1 H46
SECTION 8: MAINTENANCEDepending on your water quality, it may be necessary to perform maintenance on your fi lter system in order to ensure continued p
8) Pour the recommended amount of MPH adder into the fi lter media and add water back to fi lter to expel any air pockets in the fi lter vessel. 9)
9-1Limited Warranty Please read and complete the following warranty and mail the bottom half within 10 days of purchase CUNO Incorporated warrants to
TABLE OF CONTENTS SECTION DESCRIPTION 1 GENERAL INFORMATION 2 BEFORE INSTALLATION 3 INSTALLATION 4 PLUMBING SYSTEM CLEAN-UP 5 BACKWASHING INSTRUCTI
SECTION 2: BEFORE INSTALLATIONInspecting And Handling Your Filter:Inspect the equipment for shipping damage. If damaged, notify the transportation co
pHThe pH of water measures its acidity. Water with a pH of less than 7.0 is acidic, above 7.0 it is alkaline, and a pH of 7.0 is neu-tral. The lower t
a. Make certain no water is being drawn. Open spigot nearest pressure tank. When pump starts, close spigot and measure time (in seconds) to refi ll pr
2-4 Facts To Remember While Planning Your Installation:1) All installation procedures MUST conform to local and state plumbing codes.2) Al
SECTION 3: IMPORTANT INSTALLATION INSTRUCTIONSProper installation sequence of water conditioning equipment is very important. Refer to the following
Commentaires sur ces manuels